Practice NetApp NCSIE ONTAP NS0-183 exam. Online Exam Practice Tests with detailed explanations! Pass NS0-183 with confidence!
NS0-183 - NetApp Storage Installation Engineer, ONTAP Practice Tests 2021 | VCE4Plus
NEW QUESTION 26
After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)
- A. Re-seat the IOM module.
- B. Reconnect the SAS cable.
- C. Re-seat the SAS card.
- D. Perform a takeover-giveback.
Answer: A,B
NEW QUESTION 27
You must replace a FAS2750 switchless cluster with an AFF A220 switchless cluster for a customer. The customer requires that you transfer the data from the FAS2750 cluster to the AFF A220.
In this scenario, which two methods would you use to migrate the customer's data? (Choose two.)
- A. Establish an SVM-DR relationship between the two clusters and activate the destination SVM.
- B. Install SAS cables between the two clusters and use the vol move command.
- C. Provide cluster switches and build a 4-node cluster, then use the vol move command.
- D. Remove all of the HDD drives from the FAS cluster and install them into the AFF cluster.
Answer: B,C
NEW QUESTION 28
Click the Exhibit button.
As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.
In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)
- A. private network
- B. cluster LIFs
- C. client network
- D. management LIFs
Answer: A,B
NEW QUESTION 29
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A. The Config Advisor version you are using requires a plugin for AFF controllers.
- B. Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- C. AFF A220 controllers with internal disks support only single-path HA.
- D. Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
Answer: D
NEW QUESTION 30
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. A controller model of the same type must be used to replace the impaired node.
- B. You can change any drives or disk shelves as part of this replacement procedure.
- C. You must move the boot device from the impaired node to the replacement node.
- D. The boot device must remain intact and must not be removed from the impaired node.
Answer: A,C
NEW QUESTION 31
You completed an ONTAP cluster deployment as a reseller engineer. During the knowledge transfer process to the customer, they ask for proof that the array has correct multi-path HA cabling deployed and that the array is error free.
Which documentation output would you present to the customer to satisfy this requirement?
- A. NetAppDocs output
- B. Config Advisor output
- C. Active IQ Unified Manager output
- D. Active IQ OneCollect output
Answer: B
Explanation:
Explanation/Reference: https://docs.netapp.com/platstor/topic/com.netapp.doc.hw-controller-add/GUID-64A51339-
1F03-451C-B062-9F97E772817E.html
NEW QUESTION 32
While troubleshooting an issue with a newly installed system, you used the system controller environment show command.
In this scenario, which issue would be diagnosed with this command?
- A. shelf cabling issues
- B. controller hardware issues
- C. controller configuration issues
- D. controller version issues
Answer: B
NEW QUESTION 33
Which statement is true about cluster interconnect?
- A. It is needed for the replication network between clusters.
- B. It is a management network for cluster administration and can be used for interconnect LIFs.
- C. It provides the core data network communication.
- D. It transports the data between nodes if a Data LIF has a non-optimized path.
Answer: D
NEW QUESTION 34
You create a new CIFS data LIF with the default failover group.
In this scenario, where will the new LIF failover if the node that owns the new LIF panics?
- A. to any available port in the same subnet
- B. to any port in the cluster that is administratively up
- C. to any available port listed in the broadcast domain
- D. to any port in the cluster that is operationally up
Answer: C
NEW QUESTION 35
When you install a new ONTAP 9.7 4-node cluster, which network type is required?
- A. cluster interconnect
- B. intercluster network
- C. data network
- D. peering network
Answer: A
NEW QUESTION 36
When you install a new ONTAP 9.7 4-node cluster, which network type is required?
- A. cluster interconnect
- B. intercluster network
- C. data network
- D. peering network
Answer: A
Explanation:
Explanation/Reference: https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-nmg/Network%20and%20LIF%
20management.pdf
NEW QUESTION 37
What are two types of load balancing methods available in multimode interface groups? (Choose two.)
- A. broadcast domain-based load balancing
- B. IP-based load balancing
- C. port-based load balancing
- D. LIF-based load balancing
Answer: B,C
NEW QUESTION 38
Click the Exhibit button.
A customer has a 2-node FAS8200 cluster with four DS212C shelves with 10 TB SATA drives.
Referring to the exhibit, an aggregate will be created with which default RAID type?
- A. RAID_DP
- B. RAID4
- C. RAID1
- D. RAID_TEC
Answer: D
NEW QUESTION 39
You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?
- A. Interoperability Matrix Tool (IMT)
- B. Hardware Universe (HWU)
- C. mysupport.netapp.com site
- D. Active IQ Config Advisor
Answer: B
NEW QUESTION 40
Click the Exhibit button.
You are receiving AutoSupport e-mail from both controllers, but Active IQ is showing updates from only node cl-01-02.
Referring to the exhibit, what is a reason why Active IQ is receiving AutoSupport updates from only node cl-01-02?
- A. A firewall rule is blocking the AutoSupport.
- B. The service processor is not configured.
- C. The cluster management LIF is down.
- D. The mail host is blocking the AutoSupport.
Answer: A
NEW QUESTION 41
You have installed and configured a new AFF C190 cluster with ONTAP 9.7. Your customer wants you to install the latest version of ONTAP.
In this scenario, what are two methods to update ONTAP? (Choose two.)
- A. Use ONTAP System Manager to upload and install the new software image.
- B. Use ONTAP System Manager to download and install the new software image.
- C. Use a USB drive with the new software image and let ONTAP automatically boot.
- D. Use the cluster image package get and cluster image update commands.
Answer: B,D
NEW QUESTION 42
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- B. Educate the onsite engineer about how to manually log support calls.
- C. Ensure that Active IQ Config Advisor is installed.
- D. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
Answer: A,D
NEW QUESTION 43
You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.
Which type of SVM needs to be created to complete the installation?
- A. data SVM
- B. system SVM
- C. multitenancy node SVM
- D. admin SVM
Answer: A
NEW QUESTION 44
Which two commands verify that AutoSupport is working as expected?
- A. autosupport history show
- B. autosupport check show
- C. autosupport test show
- D. autosupport show
Answer: A,B
NEW QUESTION 45
You must cable a new AFF A700 with two DS224C shelves that are fully populated with 15.3 TB SSDs. You want to ensure that the maximum bandwidth between the disks and the controllers is reached.
In this scenario, according to NetApp best practices, which type of cabling should you use?
- A. direct connected HA
- B. multipath HA
- C. quad-path HA
- D. single-path HA
Answer: C
NEW QUESTION 46
What is the maximum port speed of an Ethernet port on a Cisco Nexus 3232C cluster-interconnect switch?
- A. 200GbE
- B. 10GbE
- C. 100GbE
- D. 40GbE
Answer: D
NEW QUESTION 47
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. intercluster SnapMirror
- B. Epsilon voting
- C. intracluster SnapMirror
- D. remote cluster peering
- E. cluster database replication
Answer: A,D,E
NEW QUESTION 48
You have just completed the installation of a FAS9000 HA pair with ONTAP 9.5.
In this scenario, according to NetApp best practices, which two tests verify the HA failover functionality? (Choose two.)
- A. Power cycle the node.
- B. Invoke a system core.
- C. Pull the motherboard out of the slot.
- D. Disconnect the HA interconnect cabling.
Answer: A,B
NEW QUESTION 49
Which two NetApp features encrypt storage data? (Choose two.)
- A. TPM
- B. NVE
- C. NVMe
- D. NSE
Answer: B,D
NEW QUESTION 50
When completing a new ONTAP 9.5 cluster base installation, which three SVM types will be present on the system by default? (Choose three.)
- A. admin SVM
- B. system SVM
- C. data SVM
- D. node SVM
- E. cluster SVM
Answer: A,B,D
NEW QUESTION 51
......
The best NS0-183 exam study material and preparation tool is here: https://www.vce4plus.com/NetworkAppliance/NS0-183-valid-vce-dumps.html